M10, Through Bolts - Heavy Duty, Masonry/ Concrete Anchor.

M10 - THROUGH BOLTS - CONCRETE/ MASONRY ANCHOR - All Lengths. Fixaball.co.uk sells all lengths of M10 though bolts, in zinc at the best internet prices, with free delivery. Orders placed before 2pm...
£3.31

M10 - THROUGH BOLTS - CONCRETE/ MASONRY ANCHOR - All Lengths.

Fixaball.co.uk sells all lengths of M10 though bolts, in zinc at the best internet prices, with free delivery.

Orders placed before 2pm are usually dispatched same day (Mon-Fri).

Please make your size and pack quantity selection from the drop down menus.

Through bolt, expansion, masonry anchors are used for fixing materials to non-cracked concrete/ masonry (brick/ blocks), and non-porous stone.

Advantages

  • High Performance, cost effective anchor for non-cracked substrates eg. concrete
  • Suitable for reduced embedment to avoid contact with rebars/ reinforcement cages.
  • Holes are the same diameter as the fixings so the fixing can be passed through the fixture after locating it in the right position.
  • Cold formed body provides consistent dimensional accuracy and material stability
  • High load-bearing capacity

 

Table to show important installation settings/ measurements:

All measurements in mm

Size

 

Anchor

Fixture

Diameter

Length

Max. Thickness

Hole Diameter

M6

6

50

10

-

7

65

25

5

85

45

25

100

60

40

M8

8

50

5

-

9

60

10

-

65

15

-

75

25

10

80

30

15

85

35

20

95

45

30

115

65

50

140

90

75

150

100

85

Size

 

Anchor

Fixture

Diameter

Length

Max. Thickness

Hole Diameter

M10

10

65

5

-

11 

80

20

10

85

25

15

95

35

25

115

55

45

130

70

60

140

80

70

150

90

80

180

120

110

M12

 

 

 

 

12 

 

 

 

 

80

5

-

13

100

25

5

120

45

25

125

50

30

135

60

40

140

65

45

150

75

55

180

105

85

220

145

125

300

225

205

Size

 

Anchor

Fixture

Diameter

Length

Max. Thickness

Hole Diameter

M16

16

100

5

-

18

105

10

-

125

25

5

140

40

20

150

50

30

160

60

40

180

80

60

220

120

100

280

180

160

M20

20

 125

 

22 

 

 

 160

40

20

200

80

60

 300

180 

160 

M24

24

180

30

20

26

260

115

100

300

155

140

 

Installation and Advice

  • Before installation, check the concrete’s strength in order to make sure its class/ standard is suitable.
  • The concrete base must be compact and porosity insignificant.
  • Installation temperature range for base material: -5 / + 40 ºC (80 ºC for a short
  • period of time).
  • Minimum installation depth values must always be respected: for anchors’ depth, for anchor-to-anchor distances and for anchor-to-edge distances.
  • Drilling must be performed by respecting the specified minimum depth and diameter, perpendicular to the base material’s surface. The holes on the material to be fixed may be used as templates.
  • When drilling near any reinforcement areas, special care must be taken to avoid damaging them. If drilling is aborted because a reinforcement area has been encountered, it is advisable to drill a new hole at a minimum distance of at least twice the aborted drill hole diameter. This advisable distance may be reduced, as long as the aborted hole is previously filled up with high-resistant mortar.
  • It is necessary to clean the holes thoroughly free of dust and debris with a suitably sized brush.
  • When temperature is below 0ºC, make sure water does not seep into the hole, as this fact could cause subsequent cracks on the concrete, due to ice pressure.
  • Introduce the anchor through the material to be fixed into the hole up to the embedment depth, according to the values on the table. It is possible to use a hammer to ensure the required depth. Do not apply any intermediate layer between the material to be fixed and the washer, such as sealing products.
  • Apply the specified torque with a torque wrench.
  • In the case the holes on the material to be fixed have a bigger diameter than required, it is necessary to insert a thicker washer and of a bigger diameter. But please, note that this procedure does not ensure a correct distribution of shear loads amongst all the anchors of a same group, and this shear load is applied only to the anchors with a correct diameter on the material to be fixed.

Image is for illustrative purposes only.

Please choose from the following for technical and/ or sales enquiries.

  • Fill out the website enquiry form
  • Click on the CHAT icon on the website
  • Call: 01242 522244
  • Email: sam@fixaball.co.uk

Alternative names

 

 

 

Through bolt

Through bolts

Throughbolt

Throughbolts

Zinc Through Bolt

Zinc Through Bolts

Zinc Throughbolt

Zinc Throughbolts

Galvanised Through Bolt

Galvanised Through Bolts

Galvanised Throughbolt

Galvanised Throughbolts

Stainless Steel Through bolt

Stainless Steel Through bolts

Stainless Steel Throughbolt

Stainless Steel Throughbolts

Masonry Through Bolt

Masonry Through Bolts

Masonry Throughbolt

Masonry Throughbolts

Stone Through Bolt

Stone Through Bolts

Stone Throughbolt

Stone Throughbolts

Brick Through Bolt

Brick Through Bolts

Brick Through Bolt

Brick Throughbolts

Concrete Through Bolt

Concrete Through Bolts

Concrete Throughbolt

Concrete Throughbolts

Through Bolt Masonry Anchor

Through Bolt Masonry Anchors

Throughbolt Masonry Anchor

Throughbolt Masonry Anchors

Through Bolt Anchor

Through Bolt Anchors

Throughbolt Anchor

Throughbolt Anchors

Anchor Through Bolt

Anchor Through Bolts

Anchor Throughbolt

Anchor Throughbolts